BA Aluminium profile underrun bar 120 x H100 short arms

Frequently asked questions

• What is regulation 2015/208?

  Delegated regulation (UE) 2015/208 of the Commission of 8 December 2014, completing European parliament and Council (UE) regulation N° 167/2013, concerning directives relating to vehicle functional safety, for the approval of agricultural and forestry vehicles, in particular concerning rear under-run protection systems (BAE)

• Are the under-run bars supplied complete? 

  Under-run bars are supplied complete, without the chassis mounting screws, available as an option.

• Can the under-run bar be mounted on my vehicle?

  The number of possible combinations (vehicle + accessories + body type) is infinite. You should check the feasibility yourself by downloading the 3D and the installation instructions.

• Where are the instructions for installing under-run bars?

  Installation instructions can be downloaded from our Web site https://www.pommier.eu

• Where are the under-run bar data sheets?

  The data sheets can be downloaded from our Web site https://www.pommier.eu

• Where is the approval report for my under-run bar?

  The approval report is confidential and is not available. However, on request, we can send it to the official authority (DREAL for example), which can request it directly from us.

• Can I cut down the under-run bar arms and plates?

  Yes, depending on the model, when the bar is positioned. In general, the part of the arms protruding beyond the plate, and the part of the plate protruding beyond the arms do not contribute to the mechanical strength of our under-run bars, and can be cut off, in accordance with the installation instructions.

• What is the minimum grade for the screws mounting the under-run bars on the chassis?

  Grade 10.9 minimum. For the quantity, refer to the documentation.

• Can I mount elements and accessories on the under-run bars?

  Depending on the type of bar, it is authorised. See the documentation for greater detail.

• What is the I/V?

  I/V is the modulus of inertia. It’s a physical value related to the quadratic moment, used in the strength of materials to determine the maximum bending stress applied to a section of flexing beam.
  It’s the quotient of the moment of inertia (I) by the distance of the extreme fibre at the axis passing through the centre of gravity (V).

• What is the quadratic moment?

  The quadratic moment is a value that describes the geometry of a section and is defined in relation to an axis or a point. It is expressed in the international system in m4 (metres to the power of 4). It expresses the relation to a point or to an axis, in particular to define the strength or distortion capability of a material.
  The quadratic moment is used in materials’ strength. It is essential for the computing of the strength and distortion of beams subjected to torsion (IG) and bending (Ix and Iy) loads. In fact, the strength of a section loaded along a given axis varies with its quadratic moment along that axis.

• What is I/V x Re?

  It’s the modulus of inertia (I/V) multiplied by the elastic limit of the material (Re)

• Do you supply the mounting screws to mount the under-run bars on the chassis?

  Yes, the under-run bar mounting screw kits are available as an option. See the documentation and catalogue.

• Can I cut the bumpers from the under-run bars?

  Yes, providing the minimum of 100 mm remains on each side, measured between the inner faces of the tyres (not counting any tyre swelling due to ground contact). See installation documentation.

• Is there a user manual for under-run bars?

  Yes, a user manual is available for non-fixed under-run bars. It is supplied with the under-run bar. It can also be downloaded from our Web site, in the “User documentation” section.
  This document should be given to the under-run bar user, who should keep it.

• What is tightening torque?

  In mechanics, it’s the moment exerted to tighten a threaded assembly. It’s a force applied at the end of a moment arm of length L, that is expressed in Newton-metres (N.m.).
  Tightening torque = force (F) x distance (L). In a prestressed assembly, the screw is subjected to tension and the assembled pieces to compression. The tightening torque values specified in our documentation must be respected.

• What is cataphoresis?

  Cataphoresis, also known as electro-phoresis depositing (cationic electro-depositing), is a surface treatment that electro-chemically deposits an epoxy type base on a metal surface. The piece is immersed in a bath of water-soluble paint. The paint is electro-deposited by a DC current and is uniformly bonded on the piece, including in recesses and on sharp edges.

• How does cataphoresis resist salt spray?

  Salt spray resistance with no rust is 250 h on sharp edges and 500 h on plane surfaces.

• Should a piece be finished by cataphoresis painting?

  Cataphoresis does not resist UV radiation. A paint finish should therefore be applied for any outdoor exposure. Cataphoresis is therefore frequently used, like a primer, to enhance corrosion resistance properties, or it may be used alone for non-visible parts (under vehicles, inside mechanisms and various machines, etc.).